Grind and seal concrete in Perth
Honed concrete in Perth
Honed concrete is ground to show the stone, then sealed. It costs less than a full polish and grips better when it's wet, so it's the usual finish for Perth alfresco areas and pool surrounds as well as indoor floors. We grind and seal new and existing slabs, and every job starts with a free on-site measure and quote.
- Typical Perth price
- $65 to $110 per m²
- Where it's used
- Indoors and outdoors
- First step
- Free on-site measure
Honed, polished or exposed aggregate?
All three show the stone in the concrete, so they get mixed up in quotes and on Pinterest boards. What separates them is how the stone is revealed and what's protecting the surface.
| Honed | Polished | Exposed aggregate | |
|---|---|---|---|
| How the stone shows | Ground flat, cutting through the stones | Ground flat, then refined through fine diamonds | Surface washed off while the concrete is fresh, leaving rounded stones standing slightly proud |
| Where the finish comes from | The sealer | The concrete itself | The sealer |
| Underfoot | Smooth, matte to satin | Smooth, satin to gloss | Textured |
| Grip when wet | Good, better with anti-slip in the sealer | Low at satin and gloss | Very good |
| On an existing slab? | Yes | Yes | No, it's laid new |
| Typical Perth price | $65 to $110 per m² | $100 to $220 per m² | Priced by the concreter who lays it |
| Upkeep | Reseal every few years | Dust mop, occasional re-polish | Reseal every few years |
Pick honed when you want the clean, flat look of ground concrete without paying for a full polish, or when the floor has to be safe with wet feet. If you want more shine and less resealing indoors, look at polished concrete. Exposed aggregate can only be laid new by a concreter, so it suits a fresh pour rather than an existing slab. If you already have exposed aggregate that has gone dull or patchy, we clean and reseal it.
Where honed concrete makes sense
Alfresco areas
A honed alfresco slab carries the look of a polished floor inside out to the yard, without the slip risk. It'll see barbecue fat, spilled drinks and leaves, so the sealer matters more here than anywhere else in the house.
Pool surrounds
Honed with anti-slip grit in the sealer is a common pool-surround finish in Perth. Lighter concrete stays more comfortable than dark pavers in full sun, though any slab gets hot on a 40-degree afternoon.
Garages
A honed and sealed garage floor sweeps clean and resists oil far better than bare concrete. If you work on cars or use chemicals and solvents, epoxy flooring is tougher.
Indoor floors on a budget
Inside, honed gives you the stone of a polished floor for less. The trade-off is that you're walking on the sealer, so the hallway and the kitchen will need resealing before the rest of the floor does.
The sealer is the real decision
With a honed finish, the sealer decides how the floor looks, how it grips, how well it holds out stains and how soon it needs doing again. Two slabs ground exactly the same way can look and wear very differently because of what goes on top, which is why a cheap honed quote is worth questioning.
Penetrating sealers soak into the concrete and leave a natural, matte surface. There's no film to peel or wear through, and they keep water out well, but they do less against oil and fat. Topical sealers form a thin film on the surface. They hold out stains better and can deepen the colour of the stone, from matte through to a wet look, but the film wears in traffic and can be slippery when wet unless anti-slip grit is mixed in.
Perth's sun changes the choice outside. Some cheaper acrylic sealers break down or yellow faster under strong UV, and it shows first on west-facing alfresco areas that cop the afternoon sun. Outdoors, a UV-stable sealer costs more up front and lasts longer between reseals.
New slab, existing floor or tired old patio
We grind and seal slabs that someone else has poured, so honed concrete starts in one of three places.
A new slab
Your concreter lays the slab and we come back to grind and seal it once it has hardened enough to grind cleanly. If you know you want a honed finish, tell your concreter before the pour. The stone in the mix is what you'll see, so ask what's in it. The slab should be finished as flat as possible, because high and low spots grind unevenly. And plan the saw cuts and expansion joints, since they'll show as lines in the finished floor. We'll work out timing with you and your concreter.
An existing indoor floor
Under carpet or tiles you'll usually find glue, gripper holes and old patches. Honing grinds off the glue and opens up the stone, and the holes get filled. The sealer evens out the look a little, but filled holes and cracks still show as lines. Removing a lot of tile adhesive is a separate grinding stage and adds to the price.
A tired outdoor slab
A stained, weathered patio or alfresco slab can often be honed back to clean concrete, taking surface stains and old sealer off with it. Rust and oil that have soaked deep may only lighten. A slab that's thin, badly cracked or crumbling isn't worth honing, and we'll tell you that at the measure rather than take the job.
How we hone and seal a slab
Most honed jobs take a couple of days or more on site, depending on the area and how much preparation the slab needs. Outdoor sealing needs dry weather and a dry slab, so winter rain can push the sealing day back. On hot summer days we seal in the cooler part of the morning, because sealer dries too fast on a hot slab to go on evenly.
Foot traffic is usually fine soon after the last coat, but the sealer keeps curing for days after it feels dry. Furniture, pot plants and cars need to wait longer. We'll give you the times for the sealer we use on your floor.
- Grind. Metal-bond diamonds take off the top of the slab to open up the stone and remove any glue, paint or old sealer.
- Fill. Holes, air pockets and cracks opened by the grind are filled so they don't trap dirt.
- Hone. Finer diamonds smooth out the grinding marks, stopping well short of a polish.
- Clean and dry. The slab is cleaned of slurry and left to dry, since sealer over damp concrete can cloud or lift.
- Seal. Coats of your chosen sealer go on, with anti-slip grit where the floor gets wet.
Honed concrete cost in Perth
Honed concrete typically costs $65 to $110 per square metre in Perth in 2026. That's well below a mechanical polish, which starts at around $100.
Where your floor lands in that range depends on the slab and the sealer. Tile adhesive and old coatings take extra grinding. Small areas cost more per square metre because setup time doesn't shrink with the job. Edges, steps and lots of cracks add hand work, and a UV-stable or anti-slip sealer costs more than a basic one. Resealing an existing honed floor is priced after we've looked at it, since it depends on what's on there now.
Worked examples
40 m² alfresco area$2,600 to $4,400
100 m² open-plan living$6,500 to $11,000
Based on typical Perth rates of $65 to $110 per m². Your exact price comes after the free measure.
Get an exact priceLooking after honed concrete in Perth
A honed floor is only as good as its sealer, so most of the care is about keeping the sealer in good shape.
Knowing when to reseal
Sprinkle some water on the busiest part of the floor. If it beads, the sealer is working. If it soaks in and darkens the concrete, it's time to reseal. Outdoor slabs in full sun get there sooner than shaded or indoor ones.
Sand and grit
Sand blown or walked onto the slab wears a topical sealer like sandpaper. Sweep or blow it off often, and put mats at the doors between the alfresco and the house.
Barbecue fat
Fat and marinade soak in quickly where the sealer is thin. Wipe spills straight away and keep a mat under the barbecue, since that patch of slab takes the most punishment.
Leaves and gum nuts
Wet leaves, gum nuts and flowers leave brown tannin stains that are hard to shift once they've set. Sweep them off before rain, especially under eucalypts.
Bore water rust
Plenty of Perth bores carry iron, and where reticulation hits concrete it leaves orange stains. Sealer slows this but won't stop it. Angle the sprinklers away from the slab, and treat existing stains with a rust remover made for concrete.
Cleaning
Use a pH-neutral cleaner and a soft broom or mop. Keep a pressure washer well back from the surface, or skip it, because a close, high-pressure jet can damage a topical sealer.
Honed concrete questions
Is honed concrete slippery?
Dry, it grips well. Wet, it mostly depends on the sealer. A matte penetrating sealer, or a topical sealer with anti-slip grit mixed in, gives good grip around pools and on alfresco areas. A glossy topical sealer can be slippery when wet, so tell us where the floor is and we'll choose to suit.
Is honed or polished concrete better?
Neither is better everywhere. Polished concrete suits indoor living areas where you want a shine and less upkeep. Honed suits outdoor areas, wet areas and tighter budgets. Polished inside with honed on the alfresco is a common combination, and the two can be ground to a similar stone exposure so they match across the doorway.
How long does the sealer on honed concrete last?
It depends on the sealer, the traffic and the sun. Shaded and indoor areas last longer, while busy paths and alfresco areas in full afternoon sun need resealing sooner, typically every few years. When water stops beading on the surface and soaks in instead, it's time.
Can you hone my existing patio?
Often, yes. Honing takes off surface stains, weathering and old sealer and opens up the stone underneath. Deep rust or oil stains may only lighten. If the slab is thin, badly cracked or breaking up, we'll tell you at the free measure that it isn't worth doing.
Does honed concrete suit a salt-water pool?
Yes, with the right sealer and anti-slip grit. Salt water drying on bare concrete can slowly damage the surface, so around a salt pool it matters more than usual to keep the sealer in good condition. Rinsing the splash zone with fresh water now and then helps too.
Will bore water stain honed concrete?
It can. Many Perth bores carry iron, which leaves orange rust stains wherever reticulation hits the slab. A sealer slows the staining but won't prevent it. Redirecting sprinklers is the real fix, and existing stains can often be lightened with a rust remover made for concrete.
Can honed concrete be polished later?
Yes. The sealer is ground off and the floor taken on through the finer grits, so an indoor honed floor can be upgraded to a mechanical polish later if you want more shine and no more resealing.
Free on-site measure and quote
Book your free measure
Send us a few details and we'll be in touch to arrange a time to look at your slab, measure up and price the finish you want. There's no cost and no obligation.
What helps us quote
Whether the floor is inside or outside, new or existing, roughly how many square metres, and whether it's near a pool. For a new slab, tell us when it was poured or when it's due to be poured.
Tell us about your floor
All fields are needed so we can get back to you.